Velcon®

The "0", "2", and "4" Series all-fiberglass cartridges are rated at 25, 5, and 3 microns respectively. The "2" and "4" Series are commonly used with diesel and other fuel oils, and are a compromise between filtration efficiency (cartridge life) and water removing capability. They coalesce gross water, but normally do not remove fine water haze.

The all-fiberglass "6" Series was originally developed for jet fuel service (the original MIL-F-8901 specification). It has a 2-micron rating and met the First Edition API 1581, Group I (non-additive) requirements. It has proven to be the most cost effective design in some jet fuel applications. "6" Series cartridges are also used in gasoline filtration service. However, it should be noted that the powerful detergent additives in most automotive gasolines reduce the coalescing capability of this and other cartridge designs.

"85" and "87" Series Cartridges: meet the exacting requirements of the Third Edition. The "85" Series is rated at 0.5-micron while the "87" Series is rated at 0.3 micron. Both incorporate multi-layered pleated media. The "85" Series is used in Class A and Class B (fixed) installations and has consistently shown superior dirt holding capacity in the field. The "87" Series is qualified for both Class B (fixed) and Class C (mobile) applications.

Cartridge Dimensions: 6" diameter cartridges are the current industry standard. They are offered in lengths of 11", 14", 22", 28", 33", 38", 44", and 56". However, not all series are available in all lengths or in both end cap designs. Contact us for details. 4" diameter cartridges are also offered for use with older equipment. They are available in a variety of lengths ranging from 8 to 40 inches.

• 75 psi maximum pressure differential rating
• 5 to 9 pH range
• 225 F maximum operating temperature
• Aluminum center tube
• Buna-N gaskets

• Injection molded end caps are standard on 6" diameter open end cartridges
• Aluminum end caps are standard on 6" diameter threaded base coalescer;

• All 6" diameter cartridge end caps are bonded directly to the media with high strength epoxy
• 4" diameter cartridge end caps are molded polyester resin or injection molded.

Coalescer Cartridge Construction

Threaded Base Coalescers are recommended for use in most applications. They simplify installation and replacement by eliminating the need for cover plates, center plates, nuts, washers, and gaskets. They are for use inVelcon® and other make filter / separators. Threaded base adapters are available to convert vessels presently using open end elements.

Open End Coalescers are offered with single unit construction which reduces the number of gasket seals and improves overall reliability.

All-fiberglass Media Coalescers combine depth particulate filtration with a deep coalescing structure. All-fiberglass designs have successively finer media layers to achieve depth-type fitration of particles.

Combination Fiberglass and Pleated Media Coalescers remove particles primarily in the high surface area pleated core. They have one or more layers of pleated media inside a cylinder of molded fiberglass laminations to provide an extended surface area for particuate filtration. Pleat corrugation and separation materials are used to keep pleats open for full utilization.

Coalescing and filtration performance depends largely on the fiber diameter and buk density of the fiberglass media. Both the All-Fiberglass and the Combinatiion coalescer cartridge designs incorporate phenolic resin impregnated fiberglass media. Several grades with fiber diameters ranging from 1 to 10 micrometers are used in various combinations to achieve desired results.Velcon's latest coalescer designs (85 and 87 series cartridges) achieve even higher filtration and coalescing efficiency by incorporating pure micro-glass fibers with diameters of less than 1 micrometer in the pleated media.

• Air vent and drain valves
• Epoxy coated interior, primed exterior
• 100 psi design pressure
• Threaded base coalescer cartridge
• Choice of three second stage cartridge options
• Differential pressure gauge
• Leg Assembly

Filters shown are used
with the V-818 Filter Separator

Optional Features:

• Male and female pipe union
• Velcon® CDF series elements

6000T

AC-405SP

AC-409SP

AC-51205

AC-713 1/2CR

AC-718 1/2

AC-71801

AC-71805

AC-719 1/2CR

AC-73601

AC-815 1/2

AC-822 1/2

AC-829 1/2

AC-82901

AC-829P4D

ACA-210

ACO-51201K

ACO-60901K

aco60901c

AD-51225

AD-60925

AD-61425

AD-82225

ASL-71801

CA-62202

CC-62283

CDF-210K

CDF-230K

CO-718CE

FO-456PL1T

FO-629PLF 1/2

FO-629PLF5

FO-644FG5A

FO-644PLF-1M

FO-644PLF-5M

FO-644PLF-5TB

FO-656PLF-1M

aco60905c

FO-718PL05

FO-718PL50

FO-718PLP3

FO-7361/2

G-0501

G-0591

G-0769

G-0919

G-0986

G-0995

G-1016-A

G-1045

HK100

HK-100-15

HK25-15

HP10-1

I-61487TB

I-61687TB

aco21005

I-6286

I-62885TB

I-62887TB

I-63185TB

I-63382

I-63387TB

I-63885TB

I-64485

I-64485TB

I-64487

I-64487TB

I-65685TB

LA-61801B

MP5E-1

SD-718

SO-324V

SO-414V

SO-424V

ad60925

fuel filters

SO-613GS

SO-614C

SO-616

SO-623C

SO-629C

SO-630PV

SO-633C

SO-636PV

SPH-1

SPH-2

VF-609A

VF-61EP1/2

VF-71E

SO-609VA

I-62285TB

FO-7181/2

SO-609V

ACO-61401K

I-6186T

cdf230k filter

fuel system